哈希28单双〈1〉头道底漆：填充工件底层的砂痕及微孔，增加下层涂料的附着力，也具缺陷指示作用。

First coat primer: Fill the sand marks and micropores on the bottom layer of the workpiece, increase the adhesion of the lower layer coating, and also serve as a defect indicator.

〈2〉中涂底漆：很重要的涂层部分，为面漆准备一个完整光滑的工作面，完成所有底漆工作的后一道工序，增加介入层的附着力以及具备一定的隔离作用，以保证面漆的质量稳定性。

哈希28单双Intermediate primer: an important coating part, preparing a complete and smooth working surface for the topcoat, completing the subsequent process of all primer work, increasing the adhesion of the intervention layer and having a certain isolation effect to ensure the quality stability of the topcoat.

哈希28单双〈3〉面漆：面漆分为单层漆和多层漆，是色彩的确定层和装饰保护层，单层漆我们通称为素色漆，也称普通漆，可以一层完成。多层漆分银粉系列漆和珍珠系列漆，分双层及多层施工工序完成的涂料，银粉漆是由特制铝质材料经研而成，具有较高的保护性及户外稳定性和很强的可观性，珍珠系列漆是由云母片及贝壳等材料通过高科技提制而成，是色彩丰富装饰性极强的涂料。面漆部分的喷涂质量要求很高，要做到清洁、丰满、光亮、不垂、不挂、光泽均匀、不漏喷、不花枪、流平好、不咬底、不浮躁、不偏色，这些全方面做到位，一气呵成确实不是件容易事，需要极丰富的经验和故障预排能力。

<3>Topcoat: Topcoat is divided into single-layer paint and multi-layer paint, which are the color determining layer and decorative protective layer. Single layer paint is commonly referred to as plain paint, also known as ordinary paint, and can be completed in one layer. Multi layer paint can be divided into silver powder series paint and pearl series paint, which are coatings completed through double-layer and multi-layer construction processes. Silver powder paint is made from specially made aluminum materials, which have high protection, outdoor stability, and strong observability. Pearl series paint is made from materials such as mica sheets and shells through high-tech extraction, and is a high-end coating with rich colors and strong decorative properties. The spraying quality requirements for the topcoat are very high. It is necessary to achieve cleanliness, fullness, brightness, no sagging, no hanging, uniform gloss, no leakage, no splashing, good leveling, no biting, no impatience, and no color deviation. All of these are done well in all aspects, and it is not easy to work in one go. It requires extremely rich experience and troubleshooting ability.

哈希28单双钣金喷漆漆面处理： 顾名思义，就是面漆后一道工序，待漆面干固后处理其上面的瑕疵，尽了大的努力都会流下一部分不十分的地方，那就只有后期补救了，其实喷涂得再满意的漆面都不是十分的，装车油漆都会有轻微的细鱼鳞状现象，我们通称桔皮现象，这是漆膜在流平过程中的干燥时差所产生的自然现象，当然一般人是难以察觉的，要用级的欣赏水平才能发觉，所以要骗过的眼睛，就只有进行漆面处理了，我们称为“镜面处理”。

Sheet metal spray painting and paint surface treatment: As the name suggests, it is a process after the topcoat is applied, and the defects on the surface are treated after the paint surface is dried and solidified. After making great efforts, some imperfect areas will flow down, and only later remedial measures can be taken. In fact, even the most satisfactory paint surface is not very perfect, and there will be slight fish scale like phenomena in car paint. We commonly refer to this as the orange peel phenomenon, which is a natural phenomenon caused by the drying time difference of the paint film during the leveling process. Of course, it is difficult for most people to detect, and it requires an expert level of appreciation. Therefore, to deceive the eyes of experts, the only way is to perform paint surface treatment, which is called "mirror treatment". Face treatment.

先用1500-2000目的美容砂纸进行整平研磨〈有必要时可用2500目的〉，然后用浮岩或陶土成分组成的粗蜡进行磨切，处理掉砂纸痕迹，下一步用细切蜡进行研磨〈不含硅〉，处理掉粗蜡痕迹，然后用还原剂处理以达到光泽，再用镜面处理剂彻底光环及抹痕，这时油漆以达到深层光泽了，后一道工序就是封釉，这样就可以达到级的漆面效果了。

First, use 1500-2000 mesh beauty sandpaper for leveling and grinding (2500 mesh can be used if necessary), then use rough wax composed of pumice or clay components for grinding and cutting to remove the sandpaper marks. Next, use fine cut wax for grinding (without silicon) to remove the rough wax marks. Then, use a reducing agent to achieve perfect gloss, and then thoroughly remove the halo and scratch with a mirror treatment agent. At this point, the paint achieves a deep gloss. The next step is to seal the glaze, which can achieve an expert level perfect paint surface effect.